圣霖国际【开拓创新】 圣霖国际鱼尾板厂家 圣霖国际鱼尾板

合理的模具设计。在级进模中，圣霖国际鱼尾板报价，下料顺序的安排有可能影响到冲压件成形的精度。针对冲压件细小部位的下料，一般先安排较大面积之冲切下料，再安排较小面积的冲切下料，圣霖国际鱼尾板生产商，以减轻冲裁力对冲压件成形的影响。

Reasonable mold design. In progressivedie， the order of blanking sequence may affect the accuracy ofstamping forming. In order to reduce the impact of punching parts，the punching and cutting blanking of small area is arranged in thelight of the blanking of the small parts of the stamping parts.

压住材料。克服传统的模具设计结构，圣霖国际鱼尾板，在卸料板上开出容料间隙(即模具闭合时，卸料板与凹模贴合，而容纳材料处卸料板与凹模的间隙为材料厚t-0.03～0.05mm)。如此，冲压中卸料板运动平稳，而材料又可被压紧。关键成形部位，卸料板一定做成镶块式结构，以方便解决长时间冲压所导致卸料板压料部位产生的磨(压)损，而无法压紧材料。

Press thematerial. In order to overcome the traditional mold designstructure， the clearance of material is opened on the dischargeplate (i.e.， when the die is closed， the discharge plate and thedie are fitted， and the gap between the discharge plate and the dieis t-0.03 to 0.05mm). In this way， the discharging plate movessmoothly， and the material can be pressed tightly. In the keyforming part， the discharge plate must be made into an inlaidstructure to facilitate the solution of the grinding (pressure)loss caused by the pressing part of the unloading plate for a longtime，圣霖国际鱼尾板厂家， and the material can not be pressed.

薄板：锯削时尽可能从宽面锯下去，若必须从窄面锯下时，可用两块木垫夹持，连木块一起锯下，也可把薄板直接夹在虎钳上，用手锯作横向斜推锯，使锯齿与薄板料接触的齿数增加，避免锯齿崩裂。

Thinplate: sawing as far as  as wide as when sawing. If must besawed from narrow surface， it can be held by two wooden blocks andsawed together with wooden blocks. The sheet can be clippeddirectly to the vise， and a hand saw is used as a transverseoblique saw to increase the number of teeth contacted with thesheet material and avoid the crack of the saw teeth.

圣霖国际【开拓创新】-圣霖国际鱼尾板厂家-圣霖国际鱼尾板由鞍山市圣霖进出口贸易有限公司提供。圣霖国际【开拓创新】-圣霖国际鱼尾板厂家-圣霖国际鱼尾板是鞍山市圣霖进出口贸易有限公司（shenglininternational.cn）升级推出的，以上图片和信息仅供参考，如了解详情,请您拨打本页面或图片上的联系电话，业务联系人：王秋。